home  wiki

Diff: NodeGHO-Configs

--- Version 
+++ Version 1 
@@ -0,0 +1,288 @@ 
+These are the configurations for the Linksys WRT54GS that is acting as Node GHO's router. 
+The Firmware is OpenWRT, precompiled squashfs snapshot from the OpenWRT website dated 25 May 2005. 
+Once the firmware had loaded the NVRAM was cleared and set to defaults using the ''mtd erase nvram && reboot'' command.  This gets rid of any NVRAM variables that aren't used by OpenWRT.  The filesystem was then reset using the ''firstboot'' command. 
+The WRT54GS has been set up so that each port on the switch is a separately routeable network interface.  Each port has it's own IP address and it's own subnet, separate from the other ports.  This is achieved with the ''vlanNports=X Y...'' and ''vlanNhwname=et0'' variables. 
+It is running Quagga/OSPF version 0.98.1 
+!! IFCONFIG 
+++++ 
+ root@nodegho:~# ifconfig 
+ eth0      Link encap:Ethernet  HWaddr 00:0F:66:C5:2A:D8 
+          UP BROADCAST RUNNING PROMISC MULTICAST  MTU:1500  Metric:1 
+          RX packets:566116 errors:0 dropped:0 overruns:0 frame:0 
+          TX packets:529242 errors:0 dropped:0 overruns:0 carrier:0 
+          collisions:0 txqueuelen:1000 
+          RX bytes:108273473 (103.2 MiB)  TX bytes:99490914 (94.8 MiB) 
+          Interrupt:5 Base address:0x2000 
+ eth1      Link encap:Ethernet  HWaddr 00:0F:66:C5:2A:DA 
+          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0 
+          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1 
+          RX packets:0 errors:0 dropped:0 overruns:0 frame:2230678 
+          TX packets:225 errors:0 dropped:0 overruns:0 carrier:0 
+          collisions:0 txqueuelen:1000 
+          RX bytes:0 (0.0 B)  TX bytes:11250 (10.9 KiB) 
+          Interrupt:4 Base address:0x1000 
+ lo        Link encap:Local Loopback 
+          inet addr:127.0.0.1  Mask:255.0.0.0 
+          UP LOOPBACK RUNNING  MTU:16436  Metric:1 
+          RX packets:92 errors:0 dropped:0 overruns:0 frame:0 
+          TX packets:92 errors:0 dropped:0 overruns:0 carrier:0 
+          collisions:0 txqueuelen:0 
+          RX bytes:10158 (9.9 KiB)  TX bytes:10158 (9.9 KiB) 
+ vlan0     Link encap:Ethernet  HWaddr 00:0F:66:C5:2A:D8 
+          inet addr:10.10.129.1  Bcast:10.10.129.15  Mask:255.255.255.240 
+          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1 
+          RX packets:204323 errors:0 dropped:0 overruns:0 frame:0 
+          TX packets:264039 errors:0 dropped:0 overruns:0 carrier:0 
+          collisions:0 txqueuelen:0 
+          RX bytes:41708299 (39.7 MiB)  TX bytes:48395231 (46.1 MiB) 
+ vlan1     Link encap:Ethernet  HWaddr 00:0F:66:C5:2A:D8 
+          inet addr:10.10.130.177  Bcast:10.10.130.191  Mask:255.255.255.240 
+          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1 
+          RX packets:218776 errors:0 dropped:0 overruns:0 frame:0 
+          TX packets:111202 errors:0 dropped:0 overruns:0 carrier:0 
+          collisions:0 txqueuelen:0 
+          RX bytes:23721101 (22.6 MiB)  TX bytes:20042223 (19.1 MiB) 
+ vlan2     Link encap:Ethernet  HWaddr 00:0F:66:C5:2A:D8 
+          inet addr:10.10.131.65  Bcast:10.10.131.79  Mask:255.255.255.240 
+          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1 
+          RX packets:143017 errors:0 dropped:0 overruns:0 frame:0 
+          TX packets:119278 errors:0 dropped:0 overruns:0 carrier:0 
+          collisions:0 txqueuelen:0 
+          RX bytes:32653985 (31.1 MiB)  TX bytes:28231018 (26.9 MiB) 
+ vlan3     Link encap:Ethernet  HWaddr 00:0F:66:C5:2A:D8 
+          inet addr:10.10.131.81  Bcast:10.10.131.95  Mask:255.255.255.240 
+          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1 
+          RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
+          TX packets:17368 errors:0 dropped:0 overruns:0 carrier:0 
+          collisions:0 txqueuelen:0 
+          RX bytes:0 (0.0 B)  TX bytes:1411800 (1.3 MiB) 
+ vlan4     Link encap:Ethernet  HWaddr 00:0F:66:C5:2A:D8 
+          inet addr:10.10.131.97  Bcast:10.10.131.111  Mask:255.255.255.240 
+          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1 
+          RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
+          TX packets:17355 errors:0 dropped:0 overruns:0 carrier:0 
+          collisions:0 txqueuelen:0 
+          RX bytes:0 (0.0 B)  TX bytes:1410642 (1.3 MiB) 
+ root@nodegho:~# 
+++++ 
+!! NVRAM VARIABLES 
+++++ 
+aa0=3 
+ag0=255 
+boardflags2=0 
+boardflags=0x0388 
+boardnum=42 
+boardrev=0x10 
+boardtype=0x0101 
+boot_ver=v3.1 
+boot_wait=on 
+ccode=0 
+cctl=0 
+clkfreq=200 
+dl_ram_addr=a0001000 
+et0macaddr=00:0F:66:C5:2A:D8 
+et0mdcport=0 
+et0phyaddr=30 
+gpio2=adm_eecs 
+gpio3=adm_eesk 
+gpio5=adm_eedi 
+gpio6=adm_rc 
+il0macaddr=00:0f:66:c5:2a:da 
+lan_dns=192.168.1.2 
+lan_gateway= 
+lan_ifname=eth1 
+lan_ifnames= 
+lan_ipaddr=192.168.1.1 
+lan_netmask=255.255.255.0 
+lan_proto=static 
+os_flash_addr=bfc40000 
+os_ram_addr=80001000 
+pa0b0=0x170c 
+pa0b1=0xfa24 
+pa0b2=0xfe70 
+pa0itssit=62 
+pa0maxpwr=0x48 
+pmon_ver=CFE 2004.1.30.0 
+port0_ifname=vlan0 
+port0_ipaddr=10.10.129.1 
+port0_netmask=255.255.255.240 
+port0_proto=static 
+port1_ifname=vlan1 
+port1_ipaddr=10.10.130.177 
+port1_netmask=255.255.255.240 
+port1_proto=static 
+port2_ifname=vlan2 
+port2_ipaddr=10.10.131.65 
+port2_netmask=255.255.255.240 
+port2_proto=static 
+port3_ifname=vlan3 
+port3_ipaddr=10.10.131.81 
+port3_netmask=255.255.255.240 
+port3_proto=static 
+port4_ifname=vlan4 
+port4_ipaddr=10.10.131.97 
+port4_netmask=255.255.255.240 
+port4_proto=static 
+scratch=a0180000 
+sdram_config=0x0022 
+sdram_init=0x0008 
+sdram_ncdl=0x22 
+sdram_refresh=0x0000 
+sromrev=2 
+vlan0hwname=et0 
+vlan0ports=0 5 
+vlan1hwname=et0 
+vlan1ports=1 5 
+vlan2hwname=et0 
+vlan2ports=2 5 
+vlan3hwname=et0 
+vlan3ports=3 5 
+vlan4hwname=et0 
+vlan4ports=4 5* 
+wan_hostname=nodegho 
+watchdog=5000 
+wifi_ifname=eth1 
+wifi_ipaddr= 
+wifi_netmask= 
+wifi_proto=none 
+wl0_afterburner=auto 
+wl0_antdiv=-1 
+wl0_ap_isolate=0 
+wl0_auth=0 
+wl0_auth_mode=open 
+wl0_bcn=100 
+wl0_channel=6 
+wl0_closed=0 
+wl0_corerev=7 
+wl0_country= 
+wl0_country_code=AU 
+wl0_crypto=tkip 
+wl0_dtim=1 
+wl0_frag=2346 
+wl0_frameburst=off 
+wl0_gmode=6 
+wl0_gmode_protection=auto 
+wl0_hwaddr=00:0F:66:C5:2A:DA 
+wl0_ifname=eth1 
+wl0_infra=1 
+wl0_key1= 
+wl0_key2= 
+wl0_key3= 
+wl0_key4= 
+wl0_key=1 
+wl0_lazywds=0 
+wl0_maclist= 
+wl0_macmode=disabled 
+wl0_mode=ap 
+wl0_net_mode=mixed 
+wl0_phytype=g 
+wl0_phytypes=g 
+wl0_plcphdr=long 
+wl0_radio=1 
+wl0_radioids=BCM2050 
+wl0_radius_ipaddr= 
+wl0_radius_key= 
+wl0_radius_port=1812 
+wl0_rate=0 
+wl0_rateset=default 
+wl0_rts=2347 
+wl0_ssid=snarf 
+wl0_unit=0 
+wl0_wds= 
+wl0_wep=disabled 
+wl0_wpa_gtk_rekey=3600 
+wl0_wpa_psk= 
+wl0gpio2=0 
+wl0gpio3=0 
+wl0id=0x4320 
+wl_country_code=AU 
+++++ 
+!! INSTALLED PACKAGES 
+++++ 
+http://openwrt.org/downloads/experimental/bin/packages/ntpclient_2003_194-1_mipsel.ipk 
+http://openwrt.org/downloads/experimental/bin/packages/quagga_0.98.3-1_mipsel.ipk 
+http://openwrt.org/downloads/experimental/bin/packages/quagga-ospfd_0.98.3-1_mipsel.ipk 
+http://openwrt.org/downloads/experimental/bin/packages/quagga-zebra_0.98.3-1_mipsel.ipk 
+http://openwrt.org/downloads/experimental/bin/packages/kmod-sched_2.4.30-1_mipsel.ipk 
+http://openwrt.org/downloads/experimental/bin/packages/tc_2.6.9-1_mipsel.ipk 
+http://openwrt.org/downloads/experimental/bin/packages/libpthread_0.9.27-1_mipsel.ipk 
+http://reseaucitoyen.be/diskless/openwrt/feeds/stable/libcpp_5.0.5-1_mipsel.ipk 
+http://reseaucitoyen.be/diskless/openwrt/feeds/stable/iperf_1.7.0-1_mipsel.ipk 
+++++ 
+!! /etc/quagga/ospfd.conf 
+++++ 
+ hostname nodegho 
+ password **** 
+ enable password **** 
+ log syslog 
+ ! 
+ interface eth1 
+ ! 
+ interface vlan0 
+ ! 
+ interface vlan1 
+ ! 
+ interface vlan2 
+ ! 
+ interface vlan3 
+ ! 
+ interface vlan4 
+ ! 
+ ! 
+ router ospf 
+ ospf router-id 10.10.129.1 
+ network 10.10.129.0/28 area 0.0.0.0 
+ network 10.10.130.176/28 area 0.0.0.0 
+ network 10.10.131.64/28 area 0.0.0.0 
+ network 10.10.131.80/28 area 0.0.0.0 
+ network 10.10.131.96/28 area 0.0.0.0 
+ passive-interface eth1 
+ ! 
+++++ 
+Note that there is no need for a ''redistribute'' statement here as all connected networks have already been declared with ''network'' statements.  The internal wireless interface, eth1, has been prevented from participating in OSPF with the ''passive-interface'' statement. 
+!! /etc/init.d/S40network 
+(network initialisation script) 
+++++ 
+ #!/bin/sh 
+ . /etc/functions.sh 
+ case "$1" in 
+  start|restart) 
+ #   ifup lan 
+ #   ifup wan 
+    ifup port0 
+    ifup port1 
+    ifup port2 
+    ifup port3 
+    ifup port4 
+    ifup wifi 
+    wifi up 
+    ifup lan 
+    wlc eth1 qtxpwr 12 #internal wireless to low power 
+    for route in $(nvram get static_route); do { 
+      eval "set $(echo $route | sed 's/:/ /g')" 
+      $DEBUG route add -net $1 netmask $2 gw $3 metric $4 dev $5 
+    } done 
+    ;; 
+ esac 
+++++ 
[EditText] [Spelling] [Current] [Raw] [Code] [Diff] [Subscribe] [VersionHistory] [Revert] [Delete] [RecentChanges]
> home> about> events> files> members> maps> wiki board   > home   > categories   > search   > changes   > formatting   > extras> site map

Username
Password

 Remember me.
>

> forgotten password?
> register?
currently 0 users online
Node Statistics
building125
gathering194
interested471
operational248
testing198